EN 10219-1 S355J2H Welded Pipes

EN 10219-1 GRADE S355J2H PIPES SPECIFICATION:

EN 10219-1 Grade S355J2H Pipes are high yield structural steel carbon steel pipes with YS of 355 MPa. The grade S355J2H indicates S=Structural, 355=YS, J2= Impact Test at -20 Deg C with minimum 27J energy requirement and H stands for Hollow. Trio Steel is a leading supplier and exporter of EN 10219-1 S355J2H Welded Pipes. These pipes are manufactured as per the EN 10219-1 Standard which is a british standard. EN 10219-1 S355J2H is also an equivalent for API 5L X52 Grade.

EN 10219-1 S355J2H Welded Pipes are mild steel pipes and tubes which are low-cost Low Carbon Steel Pipes and Tubes with maximum 022 % carbon content with a combination of max 160 % manganese easy to form and shape. These pipes are manufactured as per EN Specification and are commercially known as CS pipes or MS pipes.

Trio Steel is a Leading Stockist, Supplier, and Exporter of EN 10219-1 S355J2H Welded Pipes.

EN 10219-1 S355J2H Welded Pipes Properties

Chemical Properties of EN 10219-1 S355J2H Welded Pipes

Carbon	Silicon	Manganese	Phosphorous	Sulphur	Molybdenum	Nickel	Chromium	Copper	Others
0.23 max	0.05 max	1.60 max	0.05 max	0.05 max	–	–	–	–	–

Mechanical Properties of EN 10219-1 S355J2H Welded Pipes

Yield Strength		Tensile Strength			Elongation A5 min
MPa min	ksi min	MPa min	MPa min	ksi min	Percentage
355	50000	470	630	–	–

Equivalent Designation

DIN	EN	BS	NFA	ASTM	ASME
–	EN 10219-1 S355J2H Welded Pipes	–	–	–	–

Materials

Type

Dimensional Tolerances

Dimensional Tolerances of EN 10210-1 Grade S355J2H Pipes

OD/Wall tolerance

Outer diameter and wall Thickness
Execution	Size Range	OD Tolerance	Wall tolerance
Hot-rolled Tube	OD – 80 mmOD; 80 mmWall	± 0.4 mm± 0.5 % of OD	± 0.7 mm± (5 % x wallthickness + 0.1 mm
Hot-rolled peeled tube	All sizesWall	+ 0.25/- 0 mm	± 0.8 mm± (5 % x wall thickness+ 0.2 mm)
Cold Worked tubecold-rolled or cold-drawn	OD 80 Wall Thickness 8	+ 0.30/- 0 mm+ 0.35/- 0 mm+ 0.40/- 0 mm*	± 0.30 mm± 0.35 mm± 0.40 mm

Straightness
The maximum deviation from the straight line is 1 mm on a gauge length of 1000 mm.

Ovality
The maximum out-of-roundness is 65% of the total outer diameter tolerance.

Standard length tolerances

Component length (mm)	OD 30-100 mm	OD 100-254 mm
10-100	+ 1.0/- 0	+ 2.0/- 0
100-600	+ 2.0/- 0	+ 3.0/- 0
600-1200	+ 3.0/- 0	+ 4.0/- 0
1200-5000	+ 5.0/- 0	+ 6.0/- 0

Delivery Executions

Delivery Executions of EN 10210-1 Grade S355JOH Pipes

Tube Ends
All tubes are provided with spotless, square cut ends. Chamfering can be done on demand.

Tube surface
Tubes are supplied without anti-corrosive treatment, but anti-corrosive treatment is available and can be done on request.

Protection
External Varnished with Black or Clear Lacquer

Mill test certificate
MTC is issued in accordance with EN 10204.

Packaging
Tubes are packaged as standard, with steel straps into hexagonal bundles with one end flush. Tubes can also be bundled in multiples. Bundle weights are adjusted as requested by the customer. Each package contains tubes from a single cast/heat only.

Marking
Every tube is set apart with tube type, heat number, steel grade, and size. Information is repeated along the whole length of the tube. Bundles are also labeled with a tag having information in both alphanumeric and by bar code.

Labeling
Material conveyed directly from our plant is labeled in accordance with automotive standard, ie with both alphanumeric and bar code information. Client particular information can be included on demand. .

EN 10210-1 Grade S355J2H Carbon Steel Seamless Pipes and Tubes
EN 10210-1 Grade S355J2H Carbon Steel Seamless Pipes and Tubes are EN specification Pipes and Tubes used for structural applications. Trio steel is one of the leading stockists of EN 10210-1 Pipes and Tubes In India, Singapore, and many countries.

Brand: Trio Steel
Manufacturer: MSL, ISMT, JSL, JINDAL, TATA STEEL,
Model: Carbon Steel Pipes and Tubes.

Dimensional Standards

Dimensional Standards of EN 10219-1 S355J2H Pipes

FEDERAL
WWP-404c is similar to ASTM A-53 except that Government inspection and continuous identification marking of electric weld and seamless is mandatory. It covers black and galvanized welded and seamless pipe for flanging, bending, and coiling and for use with fresh water, oil, steam, air, and gas onshore plus a limited number of shipboard uses. Sizes 1/8 inch through 24 inch. WWP-406c is a federal specification comparable to ASTM A-120 (withdrawn 1988). Mills can certify that A-120 pipe in a distributor’s stock meets all the requirements of WWP-406c. Rexal Tubes is the leading stockiest in India with over 800-ton stock in carbon steel seamless pipe tubes.

A.W.W.A.
C-200 covers black welded and seamless pipe intended for the conveyance of water in sizes 6 inches and larger. Specification prescribes hydrostatic test pressures for sizes of pipe covered. Tensile, flattening, and bending tests are required.

ASME

B31.1 Code for pressure piping.plants, and industrial plants.
B31.2 Fuel Gas Piping.
B31.3 Petroleum Refinery Piping.
B31.4 Liquid Petroleum Transportation Piping Systems.
B31.5 Refrigeration Piping.
B31.7 Nuclear Power Piping
B31.8 Gas Transmission and Distributing Piping Systems. Covers design, fabrication, installation, inspection, testing, and the safety aspects of operation and maintenance of gas transmission and distribution systems.

ANSI (ASME)

B36.10 American Standard for Wrought-Steel and Wrought-Iron pipe. Designates dimensions, weights, and schedule numbers for welded and seamless pipe. Schedules 10 through Schedules Double Extra Heavy (DXH/XXH).
B36.19 American Standard for Stainless Steel Pipe. Designates dimensions, weights, and schedule numbers for welded and seamless Stainless Steel Pipe, Schedules 5 through Schedules 80.

A.A.R.

M-111 covers black and galvanized welded and seamless pipe intended for coiling, bending, flanging, and other special purposes and is suitable for welding. The purpose for which pipe is intended should be stated on orders. M-111 is comparable in most requirements to ASTM A-53.
M-130 covers black and galvanized welded and seamless pipe for ordinary uses in steam, water, gas, and airlines. Sizes 1/8 inch through 12 inch. Pipe to this specification is not intended for close coiling, bending, or high-temperature service. M-130 is comparable in most requirements to ASTM A-120.

Product Description

EN 10219-1 S355J2H Welded Pipes and Tubes European standard covers specialized conveyance conditions for hot-formed or annealed hollow sections from construction steel. The pipe will be supplied in 5-7 meter arbitrary lengths with butt-weld ends and varnished to stay away from the oxidation of the steel when in storage. All pipes are fully certified and traceable with heat numbers hard stamped onto each random length. Trio Steel can supply cut lengths; long pieces and even bore from forged, machined bar to fulfill your urgent demand. Trio Steel is considered as the most reliable EN 10219-1 S355J2H Welded Pipes and Tubes Supplier from India.

Certification

Additional Requirements

Surface Protection

Application

Delivery

Available Stock at Trio Steel

Our main markets for selling are:
Available Stock at Triosteel:
Pipe Gradewise Stock At a Glance:
Tube Gradewise Stock At a Glance:
Nickel Alloys Pipes & Tubes Stock At a Glance:
Top Sellers Pipes & Tubes At a Glance:
List of Countries where Trio Steel supply Pipes / Tubes :