API 5L Pipes In Indonesia

API 5L Pipes In Indonesia

The American Petroleum Institute specification API 5L pipes are mostly used for the transportation of natural gas and petroleum. These API 5L pipes are both seamless and welded. Their main purpose is the transportation of water, oil and gas from one location to another. The capability of the manufacturer ascertains the size of the pipe.

An API 5L pipe in Indonesia is manufactured by adhering to the specifications laid down by the International Organization for Standardization (ISO) 3183. It standardizes the criteria for the materials, equipment and offshore structures for petrochemical, petroleum and natural gas industries. PSL 1 and PSL 2 are the two Product Specification Levels that have been recognized by the technical committee. PSL 1 includes pipes that are made of a standard quality whereas PSL 2 pipes have additional chemical & mechanical properties and their testing requirements also differ.

Have a look at all available variants of API 5L Pipes in Indonesia.

[/av_textblock] [/av_section]

Fill the below detail

API 5L Pipes - PSL1

API 5L Pipes
API 5L Line Pipe
API 5L Supplier
API 5L Pipe Price

API 5L Pipes - LSAW

API 5L Pipes
API 5L Line Pipe
API 5L Supplier
API 5L Pipe Price

API 5L Pipes
API 5L Line Pipe
API 5L Supplier
API 5L Pipe Price

API 5L Pipes
API 5L Line Pipe
API 5L Supplier
API 5L Pipe Price

API 5L Pipes
API 5L Line Pipe
API 5L Supplier
API 5L Pipe Price

Under this specification, the grades covered are A25, A, B. The following “X” grades are also covered: X42, X46, X52, X56, X60, X65, X70, X80. The two digits following “X” signify the Minimum Yield Strength of the pipe that has been produced in this grade.

We, at Trio Steel, stock the complete range of pipes in both PSL1 and PSL2 in seamless.

The example of API 5L X42 PSL 1 Line pipe is mentioned below:

Size: ¼” to 36″
Wall Thickness: SCH 10 to 160, STD, XS, XXS
Length: up to 12 Meters

Standard: API 5L
Product Specification Level: PSL 1
Steel Grade: X42

CHEMICAL COMPOSITION
C	Si	MN	P	S	V	Nb	Ti	Other	Carbon Equivalent
Max (b)	Max	Max (b)	Max	Max	Max	Max	Max		% maximum
									CE(IIW)	CE(Pcm)
0.26	–	1.30/	0.030/	0.030/	(d)	(d)	(d)	(a)	–	–

MECHANICAL REQUIREMENT
Tensile Requirements on Pipe body of welded pipes					Ratio		Elongation	CVN Absorbed Energy		Heat Treatment
Yield Strength (R10.5)		Tensile Strength (R)			R 10.5/ R		%	0 degree celsius
PSI	Mpa	PSI		Mpa	Max		Minimum	Min J	Min ft. lb	Wield Seam Normalizing

42,100 min	290 min	60,200 min		415 min	–			–	–

IMPACT TEST
AVG ABSORBED ENERGY			IND. ABSORBED ENERGY
MIN (JOULES)			MIN (JOULES)
27			20

Notes:

0.50% maximum for copper; 0.50% maximum for nickel; 0.50% maximum for chromium and 0.15% maximum for molybdenum. For grades up to and including X52, Cu, Cr and Ni shall not be added intentionally.
For each reduction of 0.01% below the specified maximum concentration for carbon, an increase of 0.05% above the specified maximum concentration for manganese in permissible, up to a maximum of 1.65% for grades ≥ B, but ≤ X52; up to a maximum of 1.75% for grades > X52, but <x70; up=”” to=”” a=”” maximum=”” of=”” 2.00%=”” for=”” grade=”” x70.<br=””> (c) Unless otherwise agreed, the sum of the niobium and vanadium contents shall be ≤ 0.06%.</x70;>
The sum of the niobium, vanadium and titanium concentrations shall be ≤ 0.15%
Unless otherwise agreed.
Unless otherwise agreed, the sum of the niobium, vanadium and titanium concentrations shall be ≤ 0.15%
Unless otherwise agreed, 0.50% maximum for copper; 0.50% maximum for nickel; 0.50% maximum for chromium and 0.15% maximum for molybdenum.
Unless otherwise agreed, the sum of the niobium, vanadium and titanium concentrations shall be ≤ 0.15%
Unless otherwise agreed, 0.50% maximum for copper; 0.50% maximum for nickel; 0.50% maximum for chromium and 0.15% maximum for molybdenum.

Other details:

Surface
1. All surfaces have been 100% visually inspected. The surface condition complies with API 5L standards.
2. External surface of pipe shall be coated with a layer of varnish.

NDT
All pipes will be ultrasonic tested on pipe body and pipe end as per API 5L standards:
1. longitudinal: 100% of the pipe surface
2. pipe ends not scanned by automatic ultrasonic system shall be inspected by manual UT or Magnetic Particle Examination.

Certification and traceability
All dimensions will be supplied with a 3.2 certificate according to EN 10204, endorsed by recognized and independent inspection agency. Marking shall be in SI units (X52) accordance with API requirements & mill standard.

Dimensional control
All dimensions will be supplied according to API 5L clause 9.11; In addition, the following tolerances apply:
1. Pipe body: +/- 0,75%
2. Pipe end: +/- 0,5%
3. Wall thickness: +15%, -12,5%
4. Length: -0 / +100mm

Pipe Ends

Pipe Ends are bevelled. End angle shall be 30°- 0°/+5°, root face shall be 1.6mm +/- 0.8mm and fitted with bevel protectors.

Protection

Pipes are varnished on the outside.

Available stock at Trio Steel

Carbon Steel Pipes Tubes inventory at a glance

List of Countries Where Trio Steel Supply

Our main markets for selling are

We also supply

79726

Related products

0 replies

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply Cancel reply

You must be logged in to post a comment.

Enquire Now

× How can I help you?